DUST COLLECTOR

What is a dust collector? The Airex Industries Model CI dust collector is ideally suited for schools or small industrial applications where large volume or air are required for relatively small amounts of dust collected. This dust collector is primarily designed for limited ceiling height installations.

The CI dust collector unit is divided into four basic sections, the top section of the dust collector being the storage containers for the collected waste material. The centre two sections of the dust collector are the primary and secondary filtration units. The material enters the dust collector via the inlet duct into the cyclonic separation section to remove the heavy particles. The section immediately above it is the secondary filtration area, where tubular type filters are used with various filter media available for various applications. This gives a highly efficient type of dust collector.

The material storage area of the dust collector and the secondary filtration section are accessible through large access doors which allow for easy material removal and filter maintenance of the unit. The dust collector Model CI is part of the CE series of dust collectors and designed by Airex Industries in which standardized construction methods and parts are used to create a highly efficient unit and still maintain a low cost.

The dust collector unit requires a minimum of maintenance. All parts which must be maintained are easily accessible behind the dust collector.
The dust collector unit is supplied ready to operate, requiring only connection to a power source through a starter and into the unit. The dust collector unit is ruggedly constructed and has a very convenient material storage and removal all packaged into a single completely self-contained unit.

Air to cloth ratios can be changed for extremely difficult types of material handling although the standard dust collector unit is designed for maximum efficiency in most woodworking applications. Hopper storage section are available for certain installations and automatic shaking mechanisms inside the dust collector are available for your secondary filtration section.

The Cyclotube CE dust collector is mainly highlighted by the superior output of its whirling action, but it also offers high efficiency and durability by using special fibers in the confection of the bags.
The design of the dust collector and advanced features not only meets the highest industrial standards, they put the Cyclotube CE in the enviable position of being among the top dust collectors available.

Air pollution caused by dust emissions, but fought by a dus collector, is a serious problem for most industries. Industrial hygiene and dust collector must be given more attention now that its relation to worker health has been clearly established. The principle of bag filtration included in a dust collector is recognized as the safest and most efficient for dust collection. AIREX Industries has been designing and manufacturing bag type dust collectors for many years.

Airex Industries dust collectors are designed for industrial applications, including the removal and filtration of dust, smoke and other airborne pollutants. Hazardous materials are removed from the dust collector before reaching the worker breathing zone. Reverse pulse self cleaning requires virtually no maintenance while prolonging filter life and units efficiency. This dust collector complies with environmental clean air regulations.

Cyclones are frequently used as product receivers, as pre-cleaners to high efficiency fabric-type dust collectors, or as independent collectors for coarse dusts. The Airex Cyclopulse is our unique concept of high efficiency / low cost dust collector. The diversity of its applications make it the dust collector best suited for industrial installations operating in material handling, rock, wood and metallurgical products and many others.

The cyclopulse dust collector is equipped with a cyclonic pre-separation module allowing for use in high dust loads by limiting the particles to be filtered in its media filtering module. The remarkable efficiency of this dust collector is the result of many efforts in R & D testing and will meet the most critical standards in the industry.

The Airex Cyclopulse dust collector ranks among the top available collectors for the wood processing industry and other heavy load applications.
What is a dust collector system?
What is an "industrial dust collector"?
What is a "jet dust collector"?
What is a dust collector? The Airex Industries Model CI dust collector is ideally suited for schools or small industrial applications where large volume or air are required for relatively small amounts of dust collected. This dust collector is primarily designed for limited ceiling height installations.

The CI dust collector unit is divided into four basic sections, the top section of the dust collector being the storage containers for the collected waste material. The centre two sections of the dust collector are the primary and secondary filtration units. The material enters the dust collector via the inlet duct into the cyclonic separation section to remove the heavy particles. The section immediately above it is the secondary filtration area, where tubular type filters are used with various filter media available for various applications. This gives a highly efficient type of dust collector.

The material storage area of the dust collector and the secondary filtration section are accessible through large access doors which allow for easy material removal and filter maintenance of the unit. The dust collector Model CI is part of the CE series of dust collectors and designed by Airex Industries in which standardized construction methods and parts are used to create a highly efficient unit and still maintain a low cost.

The dust collector unit requires a minimum of maintenance. All parts which must be maintained are easily accessible behind the dust collector.
The dust collector unit is supplied ready to operate, requiring only connection to a power source through a starter and into the unit. The dust collector unit is ruggedly constructed and has a very convenient material storage and removal all packaged into a single completely self-contained unit.

Air to cloth ratios can be changed for extremely difficult types of material handling although the standard dust collector unit is designed for maximum efficiency in most woodworking applications. Hopper storage section are available for certain installations and automatic shaking mechanisms inside the dust collector are available for your secondary filtration section.

The Cyclotube CE dust collector is mainly highlighted by the superior output of its whirling action, but it also offers high efficiency and durability by using special fibers in the confection of the bags.
The design of the dust collector and advanced features not only meets the highest industrial standards, they put the Cyclotube CE in the enviable position of being among the top dust collectors available.

Air pollution caused by dust emissions, but fought by a dus collector, is a serious problem for most industries. Industrial hygiene and dust collector must be given more attention now that its relation to worker health has been clearly established. The principle of bag filtration included in a dust collector is recognized as the safest and most efficient for dust collection. AIREX Industries has been designing and manufacturing bag type dust collectors for many years.

Airex Industries dust collectors are designed for industrial applications, including the removal and filtration of dust, smoke and other airborne pollutants. Hazardous materials are removed from the dust collector before reaching the worker breathing zone. Reverse pulse self cleaning requires virtually no maintenance while prolonging filter life and units efficiency. This dust collector complies with environmental clean air regulations.

Cyclones are frequently used as product receivers, as pre-cleaners to high efficiency fabric-type dust collectors, or as independent collectors for coarse dusts. The Airex Cyclopulse is our unique concept of high efficiency / low cost dust collector. The diversity of its applications make it the dust collector best suited for industrial installations operating in material handling, rock, wood and metallurgical products and many others.

The cyclopulse dust collector is equipped with a cyclonic pre-separation module allowing for use in high dust loads by limiting the particles to be filtered in its media filtering module. The remarkable efficiency of this dust collector is the result of many efforts in R & D testing and will meet the most critical standards in the industry.

The Airex Cyclopulse dust collector ranks among the top available collectors for the wood processing industry and other heavy load applications.
What are dust collectors ? Airex Industries manufacturers a full line of fabric and cartridge style dust collectors. We are committed to providing you a standard or custom product that meets your individual requirements and solves your dust collectors problems.

The Airex Industries line of cartridge type dust collectors offer extremely efficient economical systems due to the continuous venturi assisted reverse pulse jet cleaning system. The dust collectors system allows on line cleaning, without significant loading thus maintaining constant internal static pressure levels.

The Airex Industries DCCH dust collectors series distance themselves with the ability to filter highly contaminated air volumes while remaining extremely compact. The cartridges are combined with an efficient self-cleaning system of compressed air allowing the filtration of sub-micronics dust particles in a continuous operation and with a constant differential pressure loss, thanks to the dust collectors.


Our DCCH dust collectors series includes sealed mechanisms and access doors for easy access and requires no tools to carry out the change of filter cartridges.
In order to choose an adequate Airex DCCH dust collectors you need to consider the following points.

The Airex Industries portable dust collectors line can be used in applications where a fixed station is not be appropriate. Two models of dust collectors are available offering a variety of volumes. With the aid of a self supporting capture arm airborn particulate is removed from the worked breathing zone. An automatic cleaning system built into the dust collectors uses compressed air blown through the filter in the reverse direction, dislodging smoke and dust from the filter.

The solid pollutants catched by the dust collectors are then collected in a dust drawer and emptied periodically. The self cleaning system of the dust collectors can be manually or automatically activated. The self cleaning system of the dust collectors maintains unit performance without excessive maintenance.

Comparing numerous air pollution control devices and dust collectors, the dry fabric filter is by far the most efficient and reliable. Contrary to other filtering methods, variations in dust loading or air volume will not change the outlet conditions of well-designed dust collectors. Of the types of dust collectors, the pulse-jet is far superior since it allows the use of highly efficient felt filter fabric.

The dust is collected on the outside of the filter bags located beside the dust collectors. At regular intervals, a burst of metered compressed air is injected through the PULSE dust collector parabolic velocity stacks to dislodge the agglomerated dust which falls into the hopper.

dust collectors are made from various materials. Maximum filtering efficiency for the dust collectors is attained by using top quality needled felt media of appropriate weight and construction a full range of natural and synthetic felts are available to suit specific requirements; fibreglass, polyester, nylon, Nomex, etc. All bags are accessed from the top of the dust collectors, eliminating the need for dirty side entry to change and service bags.


The Modular Model M dust collectors is the ultimate solution for dust filtration of various applications. The simple and efficient technology of the Model M system integrates four principle components : the cabinet, the filter section, the hopper and the dust collectors bin.

Once the air enters the dust collectors unit, a reduction in velocity occurs and the heavy particles fall into the dust collectors bins. The fine dust is carried in the air stream upwards into the filter element. The air is propelled through the filter element included beside the dust collectors while the dust is filtered out into the inside surface. Clean air can be recirculated or exhausted outside of the dust collectors depending on the application.

The SCS are dust collectors with a mechanical "shaker". Construction of the dust collectors is solid and of industrial quality. The SCS can be equipped with a centrifugal fan, with a motor ranging from 3 to 15 H.P.
What is a "cyclone dust collector"?
What is a "portable dust collector"?